Year
2027
Manufacturer
Model
Mileage
11 mi
Condition
New
Stock Number
VD 822589
Description
Overview
This new 2027 Peterbilt Model 567 tri-axle dump truck is specced for construction dump work on and off the highway, hauling construction materials. It has a 235" wheelbase, a 144.9" cab-to-axle measurement and a 204.9" cab-to-end-of-frame measurement. The engineering-assigned GVWR is 79,500 lbs, and the GCW rating is 80,000 lbs. A 16.5' Air-Flo steel dump body built with Hardox AR 450 steel is installed on the chassis. The cab, hood, fenders and roof are white in Axalta two-stage paint, and the frame is black.
Engine & Drivetrain
Power comes from a PACCAR MX-13 Performance engine rated at 510 HP at 1,600 RPM, governed at 2,200 RPM, with 1,850 lb-ft of torque at 1,000 RPM. It is a 2026 model year engine with 2024 series emissions, and it is CARB emission compliant and meets CARB engine idling rules. The engine has a PACCAR compression brake with controls on the right-hand column, EMUX electronics architecture, a powertrain optimized for balance, a typical operating speed setting of 62 MPH and a programmed engine idle shutdown timer with an ambient temperature overrule. For PTO work it has cab-station PTO mode control and a 12-pin remote PTO/throttle provision in the engine bay. Other engine equipment includes a PACCAR 160 amp brushed alternator, a PACCAR premium starter, three PACCAR premium 12V dual-purpose batteries rated at 2,190 CCA, a 110-120V immersion-type block heater, a 2-speed fan clutch for frequent start/stops and a WABCO 25.9 CFM air compressor. It also has a high-efficiency cooling system, dual self-cleaning pre-cleaners under the hood, a firewall-mounted air cleaner, a PACCAR extended-service-interval fuel/water separator and a PACCAR MX fuel cooler. Exhaust is a single right-hand system with the DPF/SCR module under the right side of the cab, and it exits through a 7" chrome-plated steel standpipe, 24" tall, with a curved tip.
The transmission is an Allison 4500 RDS-P Gen 6 Rugged Duty Series automatic in a 6-speed configuration, with a TC-571 torque converter and a dash-mounted push-button shifter. It has Allison Neutral at Stop, auto neutral when the parking brake is set and Allison Primary Shift Schedule 1. Power goes through an SPL170 HD-XL driveline with one midship bearing and an SPL170 XL interaxle driveline to a 4.30 rear axle ratio. A single-acting electric-over-hydraulic PTO control is mounted on the dash.
Chassis & Axles
The frame has 10-3/4" steel rails out to 354", with 3/8" rail thickness and a full steel inner liner. It also has HD iron front spring brackets, aluminum frame crossmembers and a square end of frame with a steel crossmember. The front axle is a Meritor MFS20 rated at 20,000 lbs, with a 3.5" drop and Meritor wide track, mounted in a set-forward position. Steering is a Sheppard HD94 dual-gear power steering system with a frame-mounted reservoir and cooler. The rear tandem is a Meritor RT46-160 rated at 46,000 lbs. It has tandem differential locks with a speed interlock, separate dash controls for full locking, a drive axle lube pump and synthetic axle lubricant in all axles. A Hendrickson EXS13 self-steering pusher axle rated at 13,500 lbs sits 54" ahead of the centerline of the forward drive axle. It is controlled by a crossmember-mounted lift axle regulator with a dash switch and gauge, and it stows higher when lifted for more ground clearance. The engineering-assigned axle ratings are 20,000 lbs front, 13,500 lbs on the first intermediate axle, 23,000 lbs on the second intermediate axle and 23,000 lbs on the rear axle.
Braking is handled by air disc brakes up front and Bendix air cam drum brakes at the rear (16.5x7), with X30 brake drums on the drive axles. It also has upsized parking brakes, rear brake camshaft reinforcement, gusseted cam brackets, dust shields, an SBM valve and a pneumatic park brake. The truck has a 6S6M anti-lock braking system and the Bendix ESP electronic stability program with ATC, specified for end dump/roll-off trucks, along with a switch to turn off traction control. A tire pressure monitoring system is installed. Air equipment includes a heated Bendix AD-HF EP air dryer with a coalescing filter and extended purge, aluminum air tanks with pull cords, nylon chassis hose and body connections at 5' back of cab.
Suspension
The rear suspension is a Hendrickson HMX EX 460 HaulMaax rated at 46,000 lbs, with 54" axle spacing and a 70K creep rating. The front suspension uses taper leaf springs with shocks rated at 20,000 lbs, Tenneco steer axle shocks, greasable front spring pins and 80 mm front spring spacer blocks. The cab rides on cab air suspension.
Cab & Interior
This Peterbilt 567 has a 121" BBC aluminum day cab and a Metton hood with a stainless steel crown and grille and tilt assist. The cab has a Prestige interior in Sterling Gray and a thermal insulation package. The driver’s seat is a Peterbilt LX premium-level air-ride high-back seat in black fabric/vinyl with left and right armrests. The passenger side has a Peterbilt ST non-adjustable high-back vinyl seat with a left-hand armrest, a toolbox under the seat and tow hook holders. The driver gets a tilt/telescope steering column and a premium leather-wrapped multifunction steering wheel with audio and cruise controls. A 15" digital cluster display shows drive axle, engine and transmission oil temperatures, air filter restriction, brake application and trailer reservoir air pressure, turbo boost, engine percent torque, engine and PTO hours and pusher axle pressure. Comfort and tech features include a 7" infotainment display with Apple CarPlay, a midlevel four-speaker package, a radio that mutes when the transmission is in reverse, a CB antenna provision, global telematics hardware, combination fresh-air heater/air conditioning, power door locks and power windows, and two additional dash switches.
On the outside, the truck has a one-piece curved windshield, a fixed one-piece rear cab window, dark window tint and a stainless steel outside sunvisor. Mirrors are motorized, heated Peterbilt aero rear-view mirrors with bright housings and integrated convex mirrors, round hood mirrors with bright housings and a look-down mirror over the passenger door. Lighting includes projector headlights with fender-mounted turn signals, five aero LED marker lights, daytime running lights, LED stop/turn/tail/backup lights at the end of the frame and two flush-mounted load lights. It also has 2.25" fender lips, a removable bugscreen behind the grille, an air horn under the cab, a textured NFPA-compliant cab entry grab handle and intermittent electric wipers. Safety equipment includes a fire extinguisher, a triangle reflector kit and a variable-adjusting 87-112 dB backup alarm. A polished, deep-tapered aluminum bumper with a toe step cutout finishes the front end.
Body & Equipment
The body is a 16.5' Air-Flo steel dump body, Model AFT-16.5-ST-HD, with 54" sides, a 60" tailgate and a 99" overall width. The sides are 3/16" Hardox AR 450 with a 4" top rail, a dirt-shedding bottom rail and smooth sides with no gussets, topped with black-painted wood side boards. The floor is 1/4" Hardox AR 450 on 3/16" formed high-strength steel longsills, with no crossmembers. The two-panel tailgate is 1/4" Hardox AR 450 x 60", with an air-operated latch, a high-lift design and a 10" bolt-on spreader apron. The body dumps with a single-acting front trunnion telescopic hoist on a rear hinge. The hoist is fed by a slim front-mount steel doghouse reservoir and powered by a hot-shift PTO and dump pump on the Allison automatic, run from the factory PTO switch. Air-operated body controls are mounted on an aluminum tower, and two body props are included. The 10-gauge HT cabshield has a 24" length, a 6" face and a 70" width, narrowed on both sides. Other equipment includes an electric arm tarp (asphalt, low mount), a 50-ton pintle hook and plate with a trailer plug and D-rings, and a front left-side ladder with three inside steps and a shovel holder. Body lighting includes six strobes (two on the rear corner posts, two on the front of the cabshield and two on the cabshield sides) and LED stop/turn/tail, marker and clearance lights, plus a backup alarm. Rubber rear mud flaps and aluminum front splash guards are installed. The body was grit blast prepped, epoxy primed and painted Air-Flo black.
Fuel is carried in a polished 26" aluminum 110-gallon tank under the left side of the cab, with a polished non-slip fuel tank step and polished tank straps. A 24-gallon DEF tank is mounted on the left side back of cab under a polished stainless steel cover. A polished aluminum space-saver battery box with side access sits on the right side back of cab, with a battery jumper terminal under the hood. It also has a cab and sleeper power disconnect switch (Kissling 300A) and a low voltage disconnect system. The aftertreatment cover on the right side under the cab doubles as a non-slip aluminum entry step.
Tires & Wheels
The steer axle runs Continental 20-ply 315/80R22.5 HSC3 tires on Alcoa 22.5x9.00 high-polish aluminum wheels. The tandem drives run eight Continental 16-ply 11R22.5 HSC3 tires on Alcoa 22.5x8.25 high-polish aluminum severe-service wheels. The self-steering pusher axle runs two Continental 16-ply 11R24.5 HSR3 tires on Alcoa 24.5x8.25 high-polish aluminum wheels. All wheel positions have mirror-polished outer surfaces and a Dura-Bright finish on the outer wheels, with wheel guards on the tandem and pusher axles. Every tire position includes a TPMS sensor.
Warranty & Protection
As a new truck, this unit includes Peterbilt Class 8 Standard Coverage for 1 year/100,000 miles (160,000 km). The PACCAR MX engine has PACCAR MX Standard Coverage for 2 years/250,000 miles (400,000 km)/6,250 hours. Base emissions warranty coverage is 5 years/100,000 miles. The truck also comes with a 5-year SmartLINQ remote diagnostics/over-the-air subscription for PACCAR MX engines.