RB SCOTT CO INC

SUPERIOR GUARDIAN 7X20 For Sale In Eau Claire, Wisconsin


		
SUPERIOR GUARDIAN 7X20 at MachineryTrader.com SUPERIOR GUARDIAN 7X20 at MachineryTrader.com
SUPERIOR GUARDIAN 7X20 at MachineryTrader.com SUPERIOR GUARDIAN 7X20 at MachineryTrader.com
SUPERIOR GUARDIAN 7X20 at MachineryTrader.com SUPERIOR GUARDIAN 7X20 at MachineryTrader.com
SUPERIOR GUARDIAN 7X20 at MachineryTrader.com SUPERIOR GUARDIAN 7X20 at MachineryTrader.com
SUPERIOR GUARDIAN 7X20 at MachineryTrader.com SUPERIOR GUARDIAN 7X20 at MachineryTrader.com
SUPERIOR GUARDIAN 7X20 at MachineryTrader.com SUPERIOR GUARDIAN 7X20 at MachineryTrader.com
SUPERIOR GUARDIAN 7X20 at MachineryTrader.com SUPERIOR GUARDIAN 7X20 at MachineryTrader.com
All
Photos
Videos

For Sale Price: Call

Contact Information

Description

Carrier chassis
• Main frame constructed of wide flange structural steel beams
• Tandem axle with (8) 11x22.5 radial tires
• complete air brake system
• mudflaps on rear axle
• Travel lights with brake and directional signals
• Fifth wheel hitch
• (4) fixed, structural steel cribbing legs
• Common Grease points - 1-2 locations to grease entire plant

Superior Guardian 7203 Horizontal Vibrating Screen
Supply and Installation for a 7x20 3 deck, all pertinent items and components including:
• adjustable motor base, motor sheave, screen sheave, v-belts, drive guard
• Screen and all pertinent items and components are supplied by Superior

Price includes the following items:
• 50 HP TEFC, 1800 RPM, 460 volt, 3 phase, 60 hz, screen drive motor
• screen subframe
• Screen is installed to operate in the horizontal position
• Right hand drive

Screen discharge chutes
• Roll away chute
• Constructed of 1/4" Mild Steel with 1/4" AR liners
• Top deck chute discharges over the kingpin end of the chassis or onto middle deck cross conveyor, 25% Blending gates
• Middle deck chute discharges onto middle or bottom deck cross conveyor, 25% Blending gates
• Bottom deck chutes discharges onto bottom or "blends up" to middle deck cross conveyor, 25% blending gates
• AR liners on both sides of blending gates

Fines hopper
• 3/8" AR Construction with conveyor belt lining
• adjustable rubber flashing full length

(2) 30" wide x 11' long reversing cross conveyors
• Structural steel channel main frame
• Mounted on rollers to manually move to discharge from either side of chassis
• Receive oversize material from respective middle and bottom decks
• Class II head end drive
• 7.5 HP motor, v-belt drive with drive guard
• Dodge shaft mount reducer
• Head pulley - 10" diameter drum, crown face, 3/8" diamond lagging
• Tail pulley - 10" diameter wing pulley
• Shafts - turned and polished
• Dodgebearings
• Manual screw take-ups
• Carry idlers - C5, 20 degrees trough, channel mount, spaced 26" OC
• Belting - 2 ply, 3/16" x 1/16" 220 PIW
• Belt splice - steel mechanical fasteners
• Primary belt scraper - Exterra® Belt Cleaner

60" x 29' fines conveyor (Horizontal)
• Structural steel channel main frame
• Capable of accepting a reject conveyor
• Class II head end drive
• 15 HP motor, v-belt drive
• Dodge shaft mount reducer
• Head pulley - 12" diameter drum, crown face, 3/8" herringbone lagging
• Tail pulley - 12" diameter Chevron® wing pulley
• Shafts - turned and polished
• Dodgebearings
• Manual screw take-ups
• Carry idlers - C5, 20 degrees picking, channel mount, spaced approximately 27" OC
• Return idlers - C5, flat rolls, spaced 10' OC
• Belting - 3 ply, 3/16" x 1/16" 220 PIW
• Belt splice - steel mechanical fasteners
• Primary belt scraper - Exterra® Belt Cleaner

Walkway
• 3/16" diamond tread plate along both sides and feed end of screen
• Hydraulic folding walkway on non-drive side
• Includes toe board, and two-rail handrail, bolt on
• Walkway access on both sides of the chassis with steep angle stair access
• Drain holes

Hydraulic "lift-only" leveling jacks
• (4) 5" x 18" hydraulic cylinders
• (4) manual lever valves; (1) for each cylinder
• 13HP Honda Motor gasoline over hydraulic, enclosed cabinet

Overhead Safety tie off
• Safety tie off over plant for workers to tie off when working on screen
• Folds down for transport

Cribbing Storage
• Hinged storage compartment
• Holds drive guard, screen cloth, cribbing materials, etc…

Electrical control panel
• NEMA 4 enclosure and NEMA SQUARE D electrical components
• Wired to on-plant motors
• (1) 50 HP screen drive motor
• (1) 10 HP fines conveyor drive motor
• (2) 7.5 HP reversing cross conveyors
• Amp gauge on outside of panel
• Hour meter inside panel
• Warning horn and light
• Labelled start/stop pushbuttons and E-stop pushbutton mounted on door of electrical panel
• Mounted on skid frame with lifting eyes (mounted on ditch side of plant)
• Power cables from motors to place panel 30' from plant, cable storage tray inside frame above axles
• Includes 2 extra #2 starters
• Painted to match plant

Electrical
• Required power is 480 v/ 3 ph / 60 hz
• Control panel and wiring are not included

Guarding
• Price includes standard guarding
• Customer is responsible to have guarding inspected

Paint
• (1) coat primer; (1) finish coat enamel in Superior Beige

Owner's manual
• copy included for operation and maintenance
Return to Previous Page